INDEPENDENT solution for Fiat/Alfa Romeo/Lancia CODE2 cars.
This means all vehicles 1999 - 2005, which uses precoded by chassis number keys with Megamos Crypto transponder.
NO MORE need to order keys from dealer and to wait for them.
Using Fiat Code2 modules (6,7,8,9,45) software prepares chip and shows PIN code - all you have to do is to program key into car.

INDEPENDENT solution for Alfa Romeo 156/166 cars, which uses PCF7935 transponders (ID44).
Using Alfa 156/166 module (5) software prepares PCF7935 transponder.
You DO NOT need any futher operations - just fit chip into key and start vehicle.
If old keys are erased, software shows PIN code and prepares transponder, ready to be matched with vehicle using diagnostic device.

INDEPENDENT solution for Renault/Opel Vivaro/Dacia Logan UCH cars.
This means all vehicles which uses keys and 12 - digit PIN code. NO MORE need of expencive remotes.
Using Renault UCH modules (30,31,44) software prepares PCF7936 chip and shows PIN code - all you have to do is to program key into car. Also if you KNOW 12 - digit PIN code, you DO NOT need to read eeprom from UCH module.
You can make DIRECT chip preparing using corresponding module and PIN code.

INDEPENDENT solution for Iveco Daily and Iveco Trucks, which uses keys with ID46 transponders.
NO MORE " Sorry, we can`t supply your PIN code, you have to buy new full set".
NO MORE need of expencive Iveco keys.
Using Iveco module (36) software converts PCF7936 chip into ready to be programmed into any Iveco van or truck.
If you KNOW pin code, you DO NOT need to open and read immobox, just prepare chip and program it into vehicle.
In case you don`t know it, read immobox eeprom and software will calculate and show it.

READY to START CAR transponders in 80% of modules.
Avoid needs of PIN codes and key programming procedures.

• TMPro saves your time. If you have coleague, which main job is to remove and refit locks and immoboxes, with TMPro you will not need to go to car to do key programming.This is applied for modules, which prepare ready to start car transponders. You can check this in information box below immobox picture. Just read immobox dump and using TMPro write transponder. This also means, that you do not need PIN codes anymore for these immoboxes. Your coleague refit immobox and lock and car is ready to start. You do not need to go to car to match key anymore.
  
  
• TMPro lowers your costs for original keys or remotes. Some cars like Renault,Fiat and Iveco accept for programming only expensive specific remotes and keys. NO MORE - now with one click on PROG button you can convert common transponder into ready to be matched with car.
  
  
• TMPro reduces time for finishing locksmith job. BMW,Fiat,Alfa Romeo and Lancia cars uses only preprogrammed by chassis number keys and you have to offer from dealer and wait for them. NO MORE - now using eeprom dump, readed from memory device and one click on PROG button you can program into transponder specific information anf it become ready to start or to be matched with particular car. Also you get PIN code, needed for key matching procedure.
  
  
• TMPro gives more independence in locksmith`s job. Vehicles, which uses transponders in keys can be divided into 2 groups. First is which not use PIN code. Second is which use PIN code. For second group you have to order PIN code by chassis number, to pay and to wait for it. Sometimes supplied PIN code is not correct. Also for some vehicles you have to order precoded by chassis number keys. All this steps can be bypassed, if your immobiliser is supported by TMPro. For 80% of modules TMPro prepares from immobox eeprom dump ready to start car transponder and you do not need any futher operations. Just cut newkey, put written transponder in it and start car. For the rest 20% of modules software shows immobiliser PIN code and you have to match written transponder with car. You can use key programming devices such as AD100, DEC Superscan or similar.